Difference between revisions of "How to load mbmloader from SD card"

From MILEDROPEDIA
Jump to: navigation, search
(Added follow-up)
m (fixed syntax highlighting)
Line 42: Line 42:
  
 
Example of my code:
 
Example of my code:
<pre>
+
<syntaxhighlight lang="c" line>
 
#define SCRATCH_MEM                    0x48002910
 
#define SCRATCH_MEM                    0x48002910
 
#define GLOBAL_REG_PRM                  0x48307200
 
#define GLOBAL_REG_PRM                  0x48307200
Line 70: Line 70:
 
         __raw_writel(0x04, global_reg_prm + 0x50);
 
         __raw_writel(0x04, global_reg_prm + 0x50);
  
</pre>
+
</syntaxhighlight>
 
Here is archive with compiled module and Motorola's mbmloader: [[File:Boot_from_sd.gz]]
 
Here is archive with compiled module and Motorola's mbmloader: [[File:Boot_from_sd.gz]]
  

Revision as of 20:21, 9 July 2011

Introduction

After software reset, OMAP BootROM checks scratchpad memory at address 0x48002910 where can be address of "software booting configuration".

The software booting configuration is a simple structure at the address stored

at the first location of available scratchpad memory: 0x48002910. There are two sections in this structure:

  • The first section provides devices for the booting device list.
  • The second section provides clock settings, which are applied before booting.
Devices to be put on the device list
0x00: Void, no device
0x01: XIP memory
0x02: NAND
0x03: OneNAND
0x04: DOC
0x05: MMC/SD2
0x06: MMC/SD1
0x07: XIP memory with wait monitoring
0x08 to 0x0F: Reserved
0x10: UART
0x11: HS USB

Implementation

We will use boot device "0x06: MMC/SD1" to load mbmloader and device "0x11: HS USB" to check if boot from SD was failed.

Prepare file to load

  1. You need to have original mbmloader from Milestone's NAND (first 128K) in file.
  2. Then replace string X-LOADER to MLO inside second 512 bytes block.
  3. Rename file to MLO
  4. Reduce file up to end of mbmloader code.
  5. Copy this file to the root directory of SD card. Partition should be "active" and formatted as FAT16/32. I think default formatting of SD card by Milestone is Ok.

Prepare code to software reset the Milestone

We need to create right structure inside scratch memory and to do software reset. I've selected address 0x480029B0 to store booting configuration.

I've used 2ndboot module from yakk to inject my code, because I'm not ready to develop full kernel module yet.

Example of my code:

  1. #define SCRATCH_MEM                     0x48002910
  2. #define GLOBAL_REG_PRM                  0x48307200
  3.  
  4.         scratch_mem = ioremap(SCRATCH_MEM, 240);
  5.         global_reg_prm = ioremap(GLOBAL_REG_PRM, 256);
  6.  
  7.         // Disable IRQ
  8.         local_irq_disable();
  9.         local_fiq_disable();
  10.  
  11.         // Store address of booting configuration structure
  12.         __raw_writel(SCRATCH_MEM+0xA0, scratch_mem + 0);
  13.  
  14.         // Header of booting config
  15.         __raw_writel(0xCF00AA01, scratch_mem + 0xA0);
  16.         // Size of booting config
  17.         __raw_writel(0xC, scratch_mem + 0xA4);
  18.         // First booting device is 0x06
  19.         __raw_writel(0x00060000, scratch_mem + 0xA8);
  20.         // Second is 0x06, third is 0x11
  21.         __raw_writel(0x00060011, scratch_mem + 0xAC);
  22.         // Fourth is 0x11
  23.         __raw_writel(0x00000011, scratch_mem + 0xB0);
  24.  
  25.         // software reset
  26.         __raw_writel(0x04, global_reg_prm + 0x50);

Here is archive with compiled module and Motorola's mbmloader: File:Boot from sd.gz

Put all of them together

  1. Copy module 2ndboot_mmc_usb.ko to root of SD card where MLO copied
  2. Run command: insmode /sdcard/2ndboot_mmc_usb.ko

Your phone should black screen and reboot successfuly, if your MLO file is Ok. If you remove MLO file from SD card and load module again, your phone should be in infinite loop of tries to boot from SD card (unsuccessful) and from USB, so your computer should see tries of USB enumerations every 3-4 seconds. You may "fix" your phone from that state by battery removing only (or maybe you can try to upload some mbmloader through USB, but it should be signed by Motorola).

Why all of this ?

We can try to load changed mbmloader and see which effect it has, without flash the phone. For example: you can try to change CHSETTINGS because it's not signed. Also we can try to break RSA checks in some way.

Follow-up of the process

Although no 3rd party tester has been able to repeat the scene from booting from MLO on Milestone, it is confirmed that(by another user Nothize other than the original writer SergeyZH) (on Windows) the control panel -> system -> hardware -> device manager can be used to monitor the USB enumeration after the phone has entered the software boot device list state.

A standalone module has been written based on the code above to try a boot list of three 0x11(HS USB) and one 0x11 respectively and the response of the USB enumerations comply with these two sets.

The setting for MLO and USB booting should refer to the ROM code memory and peripheral booting guide.